Feeds:
Posts
Comments

Archive for the ‘Community Supported Agriculture (CSA)’ Category

Just like every other spring we’ve experienced since we started Local Roots Farm eight seasons ago, this one has been quite unusual. This March, we endured the wettest month in the PNW since November 2006. Usually, around here, November through January are when it rains the most, and the most often. Lately, we’ve noticed that the winters have been drier than normal and spring wetter. In addition to the unfortunate effect this has on the quality of the skiing, it also makes getting our year started a bit more difficult. We end every year planting cover crops and we begin each spring turning those cover crops into the soil. But when the ground is wet, you can’t work it…. and so throughout March, we mostly waited.

Using the Perfecta II as our primary tillage tool

Using the Perfecta II as our primary tillage tool

Thankfully, the weather gods were kind enough to us to provide a few opportunities to start turning fields of cover crops into fields of beds ready for seeds and transplants. We have adopted a new regime for taking a field from cover crop to seed bed that we are very pleased with. After we flail mow, we are using a Perfecta II field cultivator as our initial tillage tool. We like the fact that you can work up a field pretty quickly with it, and the action of the tool seems to encourage drying. In prior years we’ve tried spading (slow and surprisingly ineffective), disking (neither of our disks is heavy enough to do an adequate job), and tilling (slow and bad for the soil). The results from the Perfecta have been great. It slices cover crops just below the soil, killing most of the plants, and it fluffs and aerates the top few inches, promoting drying.

We follow the Perfecta with the spader. The spader works wonders when spading a field that’s already fairly clean. We like the spader because it works well when soil is damp, doesn’t require much horsepower or traction, tills deep, uncompacts the tire tracks, and doesn’t leave a hardpan below its working depth. The major drawback to the spader is that it’s very slow. 1 mph slow. It takes nearly three hours to spade an acre. But for early-season tillage, it’s probably the best tool out there because you can work a field earlier with the spader than most any other tool.

Spading

Spading a field destined for carrots

For those of you following along at home, you know we had an exceptionally cold winter that killed off nearly all of our overwintering plants, leaving us with very little early season produce to sell. We have planted nearly all of our greenhouses to fast-growing arugula, radishes, turnips, and baby lettuce…. and 100% of what we’ve been harvesting has been going to our favorite restaurants around Seattle.

d'Avignon French Breakfast radishes

d’Avignon French Breakfast radishes packed up for a restaurant delivery 

When, then, will we return to the farmers markets? A good question. We have just started harvesting from the first succession of direct-seeded beds planted outdoors. We are just beginning to see the first trickle of that bounty starting to flow in. We also have a good amount of lettuce and kale lying in wait, ready for us to begin markets again.

5000 heads of baby lettuce

5000 heads of baby lettuce

If this were an ordinary year, we would have probably started vending at the Broadway Market already… but it’s not. Siri and I are expecting our second child in less than a week and we’ve decided to hold off on farmers markets until we’ve gotten over that hurdle. Right now, we are aiming for May 11th to be our first market of the year. Come see us, and say hello to the newest addition to the farm!

Look at that garlic!

Look at that garlic!

 

 

Read Full Post »

Hello blog readers. Well, it’s been a couple months without a post from us here on the farm. It’s summer, and we are pretty busy. However, we do write a weekly newsletter for our CSA subscription program, and we will now be posting each week’s newsletter here on the blog. We’re just going to pick up in the middle of things…. I think you’ll be able to catch on:

After last week’s mini account of our farm’s history, I thought I’d write a bit about how our farm looks today. When we moved onto this property in the early part of 2011, it was just a big expanse of grass. Formerly, this farm was operated as a dairy, but it had been lying fallow for at least six years and cut for hay from time to time.

Converting what I like to call “old-growth pasture” to tilled soil is a major undertaking. We have a diverse mix of plants in our pasture fields, but the dominant species are various types of grass, and the dreaded buttercup. In order to create a soil medium that will successfully grow vegetables, it’s necessary to kill (or at least mortally wound) these perennial grasses. The first step is plowing. For our big initial field preparations, we hire a neighbor with a big tractor and a big two-bottom plow. The plow undercuts the soil at a depth of about 15”, and inverts it, flipping and burying the grass where it will theoretically perish for lack of sunlight.  The plow leaves a sort of wavy pattern on the top of the soil. After a certain amount of time, we either decide the grass has been buried long enough to die, or we have to plant so we just forge ahead. Then it’s time to disk. The disk is actually a series of rolling disks, set on their edges, that we drag across the field, perpendicular to the plowed waves. It breaks up large clods of dirt and begins to level out the ridges. Disking is a very bumpy tractor job.

Once the field has been plowed and disked, we use different tools to break up and smooth out the soil, partly depending on the time of year and how wet the soil is, and partly depending on what we plan to plant in the field. After three years of continuing to break new ground on our farm, we now have about 25 acres that have been plowed and prepared for planting. This year, 15 acres will be used to grow vegetable crops over the course of the year, and the other 10 are either being rested after a year or two of vegetable production or are recently plowed fields that we are “bare fallowing” in an effort to bring the grass and other perennial weeds more under control. Despite our best efforts, the old-growth pasture grasses are amazingly tenacious. They have deep and complex networks of roots, and they propagate with underground runners that can pierce straight through a full-size potato and grow several feet long in a single season. Bare-fallowing helps clean up the patches of grass that survive plowing. We use tractor-mounted tools that undercut or drag out the grass roots without disturbing the soil structure or pulverizing soil aggregates. Finally, all of our fields get a sowing of cover crops before the winter rains set in. Cover crops protect soil against erosion during the winter, and when we turn them under in the spring, they build organic matter in our soil. More on that next time!

Box Contents for July 23rd

1 bunch red beets

1 small bunch carrots

1 bunch collards

1 bunch sweet onions

2 zucchini

1 bunch baby bok choi

1 head Samantha red oakleaf lettuce

4 ‘Miniature White’ salad cucumbers

1 bunch dill

Large Box Additions

First tomatoes!

Sage

Flashy Trout’s Back lettuce

Next week’s produce (we think): carrots – potatoes – scallions – fennel – chard – savoy cabbage – broccoli (maybe) – cukes & zukes!

Ideas and info for this week’s produce

Beets  – Beets are making their first appearance in the CSA boxes this week. We grow three different varieties of beets, which you will probably see each of at some point this year, but today you are getting the classic red beet. The simplest way to make your beets is to boil them whole. No need to peel, just put them in a small pot with enough water to cover, and boil until the beets are easily pierced with a paring knife. Drain, and run under cold tap water. The beets’ skin will easily slip off. Then you may use the cooked, peeled beets however you like. I am pleased that our dill crop is ready to pick in time for this week’s box, because I think dill is a great accompaniment to both beets and cucumbers. Cubed chilled beets, cucumbers, and slices of sweet onion would make a lovely salad, either with a simple vinegar dressing or some kind of creamy addition (yogurt, sour cream), topped off with a sprinkle of minced dill.

Speaking of cucumbers:

Cucumber – I think cucumber is one of the most popular items we include in the CSA. Just about everyone enjoys cucumbers, and they are easy to eat, even if you feel overwhelmed by cooking some of your other vegetables. We have planted a LOT of cucumbers this year, and we expect to be able to give them in the box regularly from now through mid-September. Cukes should be stored in a sealed container the fridge, and will keep at least a week if un-cut. All of these cucumbers will work for the refrigerator pickle recipe. One large or two medium cucumbers will probably fill a quart jar.

Recipe – Refrigerator Pickles

Slice cucumbers into ¼” thick rounds. Slice half an onion and a sweet pepper into strips. Pack vegetables into a quart jar. Roughly chop dill and add to jar. In a saucepan, bring to a boil ¾ cup apple cider vinegar, ½ cup water, ½ cup sugar (or honey), 1 teaspoon peppercorns, 1 ½ teaspoons mustard seed and pour over cucumbers to fill jar. Leave uncovered and chill for 24 hours. Cover, and keep in fridge. Pickles will keep in the fridge for several weeks.  (You can also make a half recipe.)

Beet Greens – What with all the roots this week, along with the zucchini and cucumber, your box is a bit light on cooking greens…. But don’t forget about your beet greens! Cook just like kale or chard (beet greens and chard are the same species!). More recipes in today’s email.

Read Full Post »

It’s been a long while since we updated the blog. And no wonder. The weather for the past month has been amazing. Especially, with the memory of the past two cold and wet springs still fresh in our mind. This time of year is probably the most stressful around here. We have hundreds of thousands of little seedlings in the greenhouse waiting to be transplanted, we have fields growing cover crops waiting to be mowed, disked, spaded, and made into beds for seeding or transplanting…. if only it would dry out enough for us to work the soil. Well, this year we have mostly been spared the stress that comes from too much rain in the spring.

Mowing cover crops

Mowing cover crops

Indeed, with the wonderfully warm and dry weather we’ve had, we’ve been wonderfully busy. The Broadway Farmers Market started in April, and the Duvall Market started in early May.

Harvesting Radishes

Harvesting Radishes

Broadway Market

Broadway Market

We built our new NRCS funded greenhouse and immediately planted it with tomatoes. Our second round of tomatoes, and our peppers and eggplant will be going in next week.

First round of tomatoes

First round of tomatoes

We have already seeded or transplanted around 4 acres of veggies, and in the coming weeks we’ll be putting in a whole lot more.

Emerging zucchini

Emerging zucchini

Transplanting Brassicas

Transplanting Brassicas

Seeding Beets

Seeding Beets

Once the plants are in the ground, comes the task of watering, weeding, and otherwise caring for them. Before the rain returned again last week, we were forced to start irrigating earlier than I can ever remember.

Lettuce and drip tape

Lettuce and drip tape

We also got out and did some tractor cultivation. Here’s a video I made while cultivating lettuce. The black object that keeps flashing through the screen is the steering wheel.

Wheeeee

Wheeeee

Read Full Post »

This past fall, a journalist was interviewing Siri and me, and asked us what made the biggest difference in our recent success. Neither of us had an immediate answer, but before my brain really had time to decide whether I meant it or not, I blurted out, “Having Felix.”

Thanks!

Thanks!

At first blush, it sounds crazy. How could having a child be the primary reason our small business, which until recently seemed to require both Siri and I to never stop working, was doing so well? But when Felix was born, it quickly became apparent that our farm was no longer the most important thing in our life, and working long hours, 7 days-a-week was no longer a possibility. At the same time, that same farm is what earns us enough money to pay for insurance, food, our mortgage, etc. Having a baby forced us to get creative, to get a little bigger, to become more efficient, to pay our employees more so they’d stick around for more than one season, to refine what we grow, focusing on the most profitable crops, and it has definitely worked.

IMG_3370

Success!

I can definitely say, it hasn’t been easy. The transition in 2011 from old farm to new with infant baby in tow was unquestionably the hardest thing I’ve ever done, and probably will ever do. But we seem to have emerged out the other side substantially better for having made the transition. Indeed, Siri and I have been talking all year about how we could possibly afford to buy the 40 acres next door.

Our farm is on the right, the new 40 are on the left.

Looking South, our farm is on the right (with all the vegetables growing on it), the new 40 acres are on the left (with all the dairy infrastructure on it).

The 40 acres we have been farming for the past two years was originally the West half of an 80-acre dairy that operated here for over 100 years. When we purchased our 40 acres, the seller subdivided the property into two 40-acre parcels and sold us half, as we couldn’t afford all of it (at the time, at least). However, we have done very well these last two years, and, more and more, we have been thinking about how we could afford to buy the other 40 acres. Our intention this past year was to wait until the season was over, look at how much we could afford, and put in an offer. But back in November, the seller called me to let me know that he had just received an offer that he was going to accept unless we could come up with a better counteroffer. So much for waiting until the year was over! That week, we scrambled to get a counter offer in. The seller accepted our offer in early-December, and for the past few months, we have been working to find financing we could afford (more on that later)

Farm from the East. Note all the barns, manure lagoon, etc

These new 40 acres are a wonderfully complicated mix of well drained areas, poorly drained areas, massive barns, dilapidated dairy buildings and infrastructure, and a million gallon manure lagoon. In the near future, much of the infrastructure is going to prove to be a bigger headache than asset. It’ll be expensive to maintain, a possible liability, and much of the fields are currently too wet to farm. So why did we make an offer on this property again?

The driveway dividing the property during the flood this past February.

The driveway dividing the property during the flood this past February.

One of our farming goals is to grow more extensively so that we can reduce the amount of inputs we use to grow veggies. That is to say, we believe that by fallowing large amounts of our acreage, we can grow our own fertility through cover cropping. Another of our goals is to pay our employees a fair wage. We are still looking for the scale that gets us there, but it seems like it’s a bit bigger than we are now. In order to fallow half our land each year, and in order to make enough to pay all our employees more, we simply needed more dry acres than our 40 acres has (if our whole farm was flat and well drained, I think we’d have enough ground now, but it isn’t). Together, these 80 acres have somewhere between 30-40 dry acres, which is as much as we believe we’ll need to get where we want to go. Fixing the drainage issues and having 80 dry acres is a topic for future blog posts.

One day, all 80 of these acres will be farmable.

One day, we hope all 80 of these acres will be farmable.

As exciting as the increased acreage, what the new 40 acres comes with is a host of barns, buildings, and assorted infrastructure. This infrastructure is priceless because the way King County enforces FEMA flood regulations essentially prohibits all construction of anything in the flood plain (other counties enforce the same regulations more favorably for farmers – another topic ripe for a blog post). So although all us farmers very much need all sorts of infrastructure, we aren’t allowed to build anything. The sheer number (and poor shape) of the buildings we are buying is intimidating. Our most immediate need is to enlarge and streamline our wash station, and we will turn one of the three huge barns over there into a more efficient wash station with lots of cooler space and storage. Beyond that, we have to deal with are two other larger barns, in relatively good shape,  a falling down calving barn, a milking parlor, and office-y space. We are thinking that one of the barns will be a nice spot to host parties, events, and weddings.

Peri and Jesse used one of the barns for some of their wedding pics last summer.

Peri and Jesse used one of the barns for some of their wedding pics last summer.

We officially closed last week. There’s much more to say about how this all came about, and what’s next for our farming plans. For now, we’re happy to share this news with all of you. The rest will have to wait.

Read Full Post »

Although it is barely February, if you look closely you can see signs of spring everywhere. (NB February 1st is the Celtic holiday of Imbolic, considered by some to be the true first day of spring). We just returned from a three day trip, where Siri was a presenter at the Washington State Farmers Market Conference in Vancouver, WA. We followed that event with a trip to see our friend Justin, down in the Willamette Valley in Oregon. We stayed a couple nights on a stunning property of pasture, oak trees, and grapevines, owned by some professional beekeepers. They were packing up their bees to bring them down to California for the almond pollination (spring!). We were so busy having fun that we failed to take any photos, except this one of a lovely candelabra fitted up with hand-dipped beeswax candles:

Image

We also visited a farm that I’ve been obsessively following on the interwebs for many years now, Gathering Together Farm. Their blog is incredibly detailed and beautifully illustrated with photos that are both pretty and SO useful for a farm of our size. GTF farms about 50 acres of mixed produce, and partners with Wild Garden Seed, a seed growing operation that is the source for many of our most favorite things: lettuces, interesting mustard greens, kale, Delicata squash, sweet peppers, and so much more. Wild Garden Seed’s diverse offerings of seed variety has always been impressive, but much more so now that we have dabbled a little in seed production of our own.

Anyway, we were too busy checking out GTF’s greenhouse designs, seed-starting facility, and packing station to take any photos, but their blog has it all – much better than any photos we could have taken with our little phone cameras. The climate in their part of Oregon is a bit milder than ours, and they are a few weeks ahead of us on their seed-starting schedule (spring!). They already had the first round of tomato seedlings up and growing, as well as chard, peas, onions, and a few other early crops. Although GTF has about 5 times more acreage in production than we do, the basics of their operation felt very familiar. It was both inspiring and reassuring to witness a farm operation that has been in business for 25 years and has lots of happy current and former employees, loyal customers, and owners that seem to still enjoy what they do.

Back on our farm, the signs of spring are there too, although many of them are happening behind closed doors. The obvious signs are the glowing seed-starting room, with trays of just-germinated seedlings poking up, the noticeable increase in egg production by our small home flock, and the first little flush of weed seeds that broke out in the 30×90 greenhouse after we ran the sprinkler in it last week.

Two weeks ago, we seeded our first round of veggies to be transplanted into a greenhouse: 2400 baby lettuces of various varieties.

IMG_3668

Sam, using the vacuum seeder to seed lettuce

They are growing happily under lights in our germination/seed starting room. This week, we started 4800 Walla Walla onions, 2400 shallots, and 2400 cippollini onions.

Baby baby lettuce

Baby baby lettuce

Today, we spaded some of our greenhouses, getting them ready to be planted with our first direct-sown crop of 2013 – radishes, spinach, and carrots.

Spading

Spading

Then, we tried something new. We used the tractor to seed radishes in the greenhouse (We’ve always used a one-row push seeder).

Seeding radishes

Seeding radishes

The carrots and spinach, though, we seeded using the push seeder.

Siri, seeding spinach

Siri, seeding spinach

Last week, we finally finished fixing the above-mentioned spader. Spaders are amazing tools for small farms like ours. They do deep tillage work, loosening soil deep down and breaking up compaction, but they require but require a small fraction of the horse power required for traditional tools used for this task. A spader’s drawback is that is’s a finicky, complicated contraption that has a zillion moving parts, Zerk fittings to grease, bolts that can loosen, etc. We bought ours used, and towards the end of both 2011 and 2012, we had a bearing fail putting our spader out of commission before we were ready to stop using it. Last winter, we replaced some of the main bearings. This winter, we replaced all the rest. It’s an annoying job, but it’s finally done and hopefully will keep our spader working well for a few more years….

The spader, stripped down

The spader, stripped down

IMG_3709

Good as new! *knocks on wood*

The winter and early-spring continue to be a whirlwind. Next week, we are being flown to Spokane, to speak at the annual convention of Northwest Farm Credit Services (click this link, our picture is front page on their website!!!). NWFCS is the bank that administers the Washington State Beginning Farmer loan program which is part of the complicated package of below-market-rate loans we got when we bought this place. The following week, we head back down to Oregon for the super-amazing, farmer-only Farmer to Farmer Exchange convention held at the Breitenbush Hot Springs at the base of Mt. Jefferson. By the time we get back, we hope to see some radish sprouts pushing their way through the soil in the greenhouse. Spring!

Read Full Post »

“Cultivate” is a funny word. It’s used to mean, “to tend” generically. But it also means, “to tend your crops,” by killing the competition. This year, we have been cultivating more with our tractors. I have been wanting to write a post about tractor cultivation, but it’s something quite new to me and I don’t feel like I have enough experience with it to have anything worth saying…. nevertheless, a comment on a recent post has inspired me to, at the very least, chronicle what we are doing to kill weeds…

Something that’s clear to anyone who has had a garden, or even has met a gardener, is that weeds are generally despised. They compete with our crops for nutrients and water; they shade our plants and stunt their growth; they make the place look unsightly.

Clean beds are pretty

But, there are many reasons why weeds aren’t always so bad. The worst weeds on our farm, not by prevalence but by sheer awfulness, are thistles. Their spiny leaves hurt a lot when accidentally touched, even when they are small. Nevertheless, they are a refuge for ladybugs and ladybug nymphs, beneficial insects which feast on aphids… so thistles, they aren’t all bad. Yet, I wouldn’t be sad if I were able to rid them completely from my farm…

Now, the most effective strategies for keeping the thistle (and buttercup, and lambsquarter, and pigweed, and shepherd’s purse, etc) population in check don’t actually involve tractor mounted cultivators, per se: fallowing a whole field and stale bed cultivation. The easiest way to deal with weeds is when you can take a mower or a disk to an entire field that doesn’t have any crops growing in it.

One acre left fallow adjacent to an acre being planted. The truck in the background is spreading lime, to raise the pH of the soil – we spread 4400 lbs per acre!

This year, we have taken a few fields we used last year out of production. More than anything, we simply want to rest as much of the farm as we can, so our wonderfully fertile ground can stay that way. Yet, it’s also a really easy way to keep weed populations in check. The fields we’ve been fallowing were cover cropped last fall. This spring and summer, when flushes of weeds appeared amidst the oats and vetch, we simply mowed the whole field, setting back or killing the weeds, and giving the grass another opportunity to put on more growth. Similarly, we had a few new fields plowed this year, one of which we aren’t using until next year. Every so often, we take the tractor out there and disk in all the weeds that have germinated. It takes very little time and is very effective. Next year, we anticipate that field having fewer weeds…

For fields that we do intend to plant into, to the greatest extent possible, we try to use stale bed cultivation to control weeds. Whenever you work up soil, getting it ready to plant into, you are also creating a very hospitable environment for weeds. Weather permitting, we try to have a field we are planting into spaded three weeks to a month prior to planting. In that time, weeds will have germinated and started to grow. Right before planting, we make beds with our tiller, which does in most of the weeds that had appeared since the field was spaded.

Makin’ beds and killin’ weeds

Of course, in the lovely Pacific Northwest, the weather rarely is permitting. And for a good portion of our season, dry weather windows that allow us to work the ground are few. So, we frequently spade and till the same day or week, and we don’t get the opportunity to do that sort of stale bed cultivation. Now, it sometimes happens that beds get tilled and marked, but nothing gets immediately transplanted into them. By the time we are ready to transplant into one of these forgotten beds, if it has been colonized by weeds it gets a second tilling. One observation we’ve made, is that these beds are almost always the most weed free beds on the farm. For now, maintaining good soil structure is a higher priority than killing weeds, so we won’t be double tilling all our beds any time soon. But as with everything, there are always tradeoffs to be made and other possibilities to consider.

Our fall broccoli field – cover cropped, stale bedded, spaded, tilled, and ready for transplants this week!

Once crops are in the ground, it’s much harder to kill weeds because you don’t want to accidentally kill your veggies too. Larger, modern farms use herbicide and GPS guided tractors with 30′-wide cultivators.

Big tractor cultivating corn

But back before all that, commercial farmers used tractors with special weed-killing implements mounted in front of the driver to kill weeds. They stopped making these types of tractors in the early ’80s, but small-scale farms like ours still use them because they are the right scale for our sized farms. On our farm we have a Farmall Cub from 1951 and a Kubota 245H from 1984 that we use for cultivation.

Farmall Cub, about to cultivate winter squash, Mt Rainier and Kubota 245H in the background

I have a suspicion that the terminology for these tools might vary, but on the Cub we use what we call “sweeps” and on the Kubota we use what we call “knives.”

Sweeps, and lacinato kale flowers
Knives, and rainbow chard

Basically, sweeps are sharpened shovel blades mounted on the end of an adjustable shank. They throw soil in both directions. Knives are sharpened unidirectional wings on the end of a shank. They throw soil in one direction (mostly).

The sweeps are really nice to use because they don’t require so much precision. The shovels run down the middle between rows and are a good ways away from the plants, cutting a 6″ swath and throwing soil another few inches, depending on how deep in the soil you set them. You can go pretty quickly and not worry so much about killing your plants. They seem to work well with bigger weeds and grasses, but they aren’t especially accurate because they are fairly far from the crop. Because they throw soil, sweeps seem best suited to bigger plants that can stand having soil tossed on them, like transplanted brassicas, leeks and onions, corn, etc.

Siri cultivating brassicas with the Cub

Knives (or beet knives as they are sometimes called) only throw soil in one direction and only cut in one direction, so you can cultivate very close to your plants. Knives are best suited to plants you don’t want to bury such as lettuce, carrots, and beets when they are small.

In my limited experience, knives work really well when weeds are small and the soil is dry enough to flow around the blades. As soon as the soil is clumpy or weeds are big enough to get hung up on the blade, the knives start pushing soil onto the crop you are trying to cultivate and they don’t work nearly as well. It has also been my experience that getting the depth set just right really improves the outcome. On our farm, are fields are generally flat, but with many undulations and rolls. Our bedshaper does a pretty good job squaring up our beds, but it’s really obvious when one isn’t level when I’m trying to use the knives because it’s impossible to adjust the height of the knives accurately across the bed.

Rawley cultivating carrots

The act of tractor cultivation itself can be a bit like a crazy video game. Especially when you are using the knives, the plants, spaced every 8″ or 12″, seem to be flying by at a million miles an hour. If you could take your eyes off what you are doing for a second, you’d see that you are crawling up the bed at less than 1 mile per hour. It’s fun, and a bit stressful, especially because the third row isn’t visible from the driver’s seat. This is why it’s so important to have the rows in each bed be parallel with each other. As long as the knives that you can see aren’t killing the rows of carrots you can see, you can be pretty sure the knives you can’t see aren’t killing the carrots you can’t see. Nevertheless, I tend to stop every so often and check to make sure.

One last thought about these cultivation techniques – we invested in the Kubota this past winter for two reasons. One reason was that I was the only person on the farm who could reliably get the Cub started, so it was difficult to have anyone else do any cultivation (side note – the Kubota starts up every time, and after some wintertime maintenance, so does the Cub). The other reason is that the Kubota is built to use modern cultivation tools that you can buy at your local tractor store. Finding an inexpensive Farmall Cub or Super A is easy. They were some of the most popular tractors ever made. However, the Cub uses what’s essentially a proprietary system that was discontinued sometime in the 1960s. Finding cultivator parts for the Cub is an exercise in ebay frustration…. do you know how much it costs to ship hundreds of pounds of steel across the country? More than the parts costs. It is possible to have a local welder adapt the Cub’s toolbar to take the standard sized modern shanks and clamps, but that’s pretty expensive too. Sweeps and knives can be purchased relatively inexpensively from a tractor dealer. Farmall cultivators can be found on ebay, craig’s list, etc. But as far as I can tell, they never made knives. Whether knives are worth investing in, I can’t say. But I like having them because I like having options when it comes to killing weeds. Some crops like one cultivator over another, as do some soil conditions.

On that note, we also invested in a tine weeder this year.

The tine weeder, ready to tickle the weeds

We still haven’t used it much, but as our big fall plantings of beets, carrots, brassicas, and radicchio all go in this month, I think we’ll start “tickle weeding” all the beds pretty soon. The tine weeder, they say, works best when the weeds are at their “white thread” stage, meaning their root is just one thread-like radicle. The tine weeder agitates the soil, gently hitting your crops too, but the agitation is rough enough to uproot the baby weeds. One reason I bought the tine weeder, is that it’s an aspirational tool, meaning we’ll really have our act together when we can get at every bed with the tine weeder at just the right stage…. This aspect of the tine weeder is also the reason we haven’t used it much. But it’s something to aspire to.

Read Full Post »

Phew. *wipes sweat from brow* That was one amazing month. For nearly three straight weeks it was warm and dry. The weather was so nice that when rain started falling last week it felt like a relief. It’s watering in all our seeds and transplants. It’s giving us time to regroup.

While our neighbors were making real hay in the sun, we made proverbial hay…

The farm from the air

We have been doing (or paying for) a lot of infrastructure improvements out here. During every dry-ish spell from January through mid-May we’ve been getting truckloads of fill delivered to build a farm pad.

Hill of fill… it took about 500 dump truck loads to build our pad.

What’s a farm pad? Our farm is in a flood plain and every so often, we get a flood. A farm pad is essentially a man-made hill that’s higher than the peak of a 100-year flood. Now, ours looks like this:

Top of the pad. 5000 square feet, raised up 4 feet.

While the excavation guys were here with their heavy equipment, we had them dig us a trench to bury some irrigation line.

Now we don’t have to disconnect the hose crossing the driveway every time we leave the farm.

Watching all the heavy machinery doing grading and leveling work got us thinking… Despite the wonderfully dry weather, we have a field on our farm that still hasn’t dried out enough to work. It’s lower than all the rest, it’s where about half our farm drains to, and its drainage is blocked by the driveway. Even after those three weeks of warmth, there was still standing water in parts of this field. We had hoped it would be dry enough to use this year, and it should be by mid-June. But we’ve decided to let it sit another year. Instead, we are going to hire the contractor who built our pad to grade it and improve the drainage so it’s usable earlier and more consistently…. we are hoping that happens sometime in June.

Because we’ve decided to take this area out of production this year, we needed to find more ground. We talked to our neighbor, and he let us plow an acre of his property. Until a few weeks ago, we’d always hired someone to do plowing for us. It’s something that’s difficult to do well, and when it’s not done well, can cause you lots of trouble down the line. But, a different neighbor happened to have an old two-bottom plow lying around and I wanted to try it out.

Learning to plow

Now, the way a plow works is by inverting ribbons of soil. The grass (or whatever was growing there before) is killed or set back by being turned upside-down and deprived of light. A bad plow job doesn’t invert the soil completely, resulting in strips of grass that keep living. Our 1-acre plowing experiment went fairly well, but it was far from perfect. We’ll be planting easy-to-cultivate zucchini and winter squash there, so hopefully we’ll be able to stay on top of the grass.

Speaking of cultivating, we’ve had the opportunity to do a bunch in the warm weather. The thing about killing weeds, whether by hand, with a hoe, or using tractors is that it doesn’t work nearly as well when the soil is wet. Hoes and cultivators don’t move through wet soil well, and even if they did, uprooted weeds reroot easily when there’s moisture available to them.

We have been using the Farmall Cub with a set of 4″ sweeps to cultivate bigger plants that don’t mind having soil thrown around them.

Siri using the Farmall Cub to cultivate brassicas

We also went up to Farmers Equipment in Burlington and bought a set of shanks, clamps, and beet knives for the Kubota 245H. Beet knives work well for smaller plants that you want to keep clean because the knives only throw soil in one direction.

Beet knives

The other new cultivator tool we invested in this year is a tine weeder. The tine weeder is neat because it tickles the whole bed, including the crops we planted, with it’s tines. The tines uproot weeds when they are at what’s referred to the “white thread stage” but it doesn’t harm (much) the plants we planted.

Tine weeder

So far, we haven’t used the tine weeder enough to say whether it was worth the investment. For some reason, it hangs from the 3-point frame by chains. This made it hard to adjust properly. Next time I have a free minute, I’m going to drill holes in the frame and bolt the tine weeder to it.

Of course, we’ve also been spending tons of hours seeding and transplanting.

Seeding

We now have over 3 acres planted, and have already started turning in our first few succession plantings of salad mix ingredients, turnips, and radishes.

Lastly, a quick update about our bed shaper – it’s awesome and has saved us countless hours so far. Not only do we get a tilled and marked bed in one pass, but the increased uniformity of our beds has made cultivation way easier. If anyone out there is interested in having Gary build you one, I recommend giving him a call – 206-900-9362. He hasn’t figured out a price yet, but my guess is that it’ll be somewhere in the $1000 range.

I had a few requests to post more pictures. So here they are:

Shaping & marking beds

Bed shaper disconnected from the tiller. It takes less than 5 minutes to take it off/put it on.

Beds freshly tilled & seeded into

Well, that’s probably all we have time for today. There are still thousands of little plants in the greenhouse asking to be transplanted, and millions of weeds in the field needing to be attended to… Happy spring!

 

 

Read Full Post »

What phenomenal weather we’ve had here in the PNW the past few weeks. We’ve been so busy using our new equipment, I haven’t had time to write about it. Since I last posted, we have been mowing, spading, disking, tilling, seeding, and transplanting up a storm.

Lots of brassicas

Today and yesterday we also planted about a third of an acre of potatoes. We made a furrow with hilling disks on the Cub and, after placing the seed pieces in the furrow, turned the disks around covered them up. It was an amazingly fast way to plant potatoes.

You put the potato in the furrow...

...then you cover them like so.

But the most exciting part about the past few weeks was experimenting with our modified tiller/bed-shaper.

Bed-shaper v 2.0

What we’ve created is basically what’s known as a pan-style bed shaper attached to the back of the tiller. What’s cool about it is that we can take it off and put it back on in about 5 minutes or less. And, if we ever get a new tiller, we can easily take the attachment parts off and attach the bed-shaper to another tiller. Pretty nifty.

Off

The shaper starts out as wide as the tiller, 60 inches, and funnels the soil down to 48 inches. The rear pan is adjustable up and down using a jack-screw. The sides of the rear pan are also adjustable, so it can make a bed that is between 3 and 6 inches tall. Being able to adjust the rake of the rear shaper pan was especially useful early last week when we were tilling moist soil and wanted to till super shallowly but still needed downward pressure on the bed for the shaper to work.

Using the shaper in damp soil.

I’m especially pleased with the removable row markers. They’re nothing more than 3 bolts attached to the rear pan. But combined with fact that the shaper makes the walk path too, it saves us a pass with another tractor to mark beds for transplanting, and I feel that we are ending up with straighter rows.

Straight rows of lettuce

The next modification is going to be the addition of hilling disks in front of the tiller. We use a reverse spinning tiller which throws soil forward, irritatingly filling the just formed walk paths with a ridge of soil. Our hope is that disks will both block this soil and also channel more soil through the main channel enabling us to make taller beds. We hope to have version 3.0 of the bed shaper up and running by our next dry spell… Until then!

Read Full Post »

Yesterday and today, Siri, Felix, and I visited three farms near Rome one unbelievably cute farm that’s about one acre, one, Caramadre, that’s about 14 acres, and another, Orto di Giobbi, that’s about 80 acres. Of the three farms we visited the 14-acre farm is organic and the other two, like us, grow organically but choose not to certify. After we’ve visited more farms on this trip, we’ll write a post (or two) about specific things we’ve seen and learned. Until then, here are some pictures and some initial thoughts and observations.

Plowed field at the tiny, hillside farm

Field of radicchio and greenhouses at Caramadre

Rows of puntarelle and escarole in one of Orto di Giobbi's many fields

All three farms are part of a new/old movement in Italy where farms sell direct to consumers. It seems that, a long time ago, like more than 30 years, all the farms in Italy used to sell directly to consumers. Every day of the week there were markets all over the cities and towns and each farm had their spots at their markets which they went to, week in and week out. The parents of the farmers we met sold at markets throughout Rome, and these farmers continue to sell at many of the same markets as their parents. However, the children of many other now-retired farms didn’t want to farm, so many of the markets around Rome were forced to allow vendors to sell fruits and vegetables they didn’t grow themselves. Whereas before most fruits and vegetables came from small farms, few larger than 10 acres, increasingly, fruits and vegetables were coming from ever larger farms, more consolidated farms.

We drove past a huge farm, harvesting hundreds of acres of carrots

Markets in Rome became much like the Pike Place Market: grocery stores with more character. Italians continue to buy fruits and vegetables from small, neighborhood markets, bread from their local panetteria, meat from their local butcher… but for the most part, the fruits and vegetables at the local markets aren’t grown by the vendor.

Puntarelle and fennel at a reseller's booth at the Mercato Esquilino

Apparently, sometime around the turn of the millenium, various organizations throughout Italy decided that this trend away from the localized, smaller-scale agriculture was a bad thing. As I mentioned in our last post, a few different groups sprang up and started American-style farmers markets throughout Italy. For instance, a group called Campagna Amica (friends of the countryside) seems to run or sponsor a bunch of markets throughout Italy; the City of Rome sponsors a market. According to one of the farmers we met, this trend towards direct marketing has been a boon for him and his smaller-scale farmer friends.

Nevertheless, the prices of vegetables here in Italy are unimaginably low. We bought beautiful heads of butter lettuce for 0.65 Euro cents each. This head of fennel only cost 0.68 cents. The quality of produce in the grocery store is very high, yet prices are very very low.

Cheap fennel, big as a baby's head!

The prices the farmers get for produce sold directly is much higher than they get when it’s sold into the wholesale chain. Nevertheless, just like us, prices for produce sold directly are heavily influenced by the retail prices of produce. One farmer told us today that the retail price for heads of lettuce are so low that he’s nearly stopped growing it… a huge contrast to our operation. The retail price of lettuce in Seattle is relatively high, and it’s one of our most profitable crops.

Yay lettuce!

One question these farm visits have raised for us is how it’s possible for farmers (here in Italy, in California, in Seattle) to make a living when they can sell a head of lettuce, a bulb of fennel, a bunch of kale for mere pennies. Clearly, huge farms are able to make a profit when they only make pennies on each item by simply moving tons and tons of their products, (not to mention paying their workers slave wages, exploiting the longterm environmental viability of their farms, using tons of chemicals, etc).

Yet, prices here are so much lower than in America, these things can’t completely explain the difference. My theory is that, despite increased consolidation of farms in Italy, they are still relatively small, production is still quite localized and seasonal (the mild climate helps), and the supply chain here is much much shorter. California (and Florida in the winter) basically supplies all of America with our produce. Your typical grocery store vegetable passes through many middlemen between the California farm where it was born and the grocery store in Massachusetts, Ohio, Texas etc where it winds up.

So what does this all mean? Does it mean small farms, selling within a regional market, directly to customers (or even into a short supply chain wholesale market) can make an honest living despite competition from large-scale, monoculture farms? Perhaps… All the farms we’ve visited so far appear quite successful in their own way. After we’ve had more time to decompress and marinate on all we’ve seen, we’ll post more details about each farm. Until then!

Until next time!

Read Full Post »

It has been a very long time since we made a blog post. Our intention when we started this blog was to post something every week. From late-Fall through late-Spring, we are able to stick to that schedule pretty well. Sitting here now, looking through the morning fog at fields of vegetables and cover crops, I’m amazed that we mustered the energy this summer for the few posts we did write.

This has been one hell of a year for Siri and I. Mostly, this has been a year filled with phenomenal good fortune combined with an ungodly amount of work. Thrown into that mix have been a handful of tragedies and misfortunes. These deaths and illnesses somehow felt both more poignant and less poignant than they otherwise might have, due to the compressed time and mental space we’ve had to process them.

Now that we are entering a slower season, we can finally stop and reflect on what we’ve accomplished this year. Until now, all of our attention has been on Felix and making sure the most important tasks were accomplished. So focused on our daily and weekly work, that the day we finalized the purchase of this farm, we didn’t stop and celebrate. We didn’t do anything. In fact, we just went back to work and didn’t even remember to tell anyone that we had completed the purchase.

And now, it’s fall. Time to finally slow down and think. I’m not trying to be self-congratulatory, but as I sit here writing, I’m amazed by the list of things we did this year. On top of raising Felix, a full-time job itself, we navigated the very tenuous purchase of our new farm, securing our low interest Beginning Farmer loans between government shut downs and threatened budget cuts aimed at our loan program. Luckily, we knew the loan process would be long, and began leasing the property in January. Once we had a signed purchase and sale agreement, we got busy moving our whole farm to this new property. Somehow we made the transition almost seamlessly. In so doing….

We built 5 greenhouses

We tried to baby-proof the fixer-upper farmhouse

We survived a big flood

We bought a couple of tractors

We grew eight acres of vegetables

We harvested a lot of food

We grew our CSA by 20 families

We had our best farmers market season ever

We grew almost 14 acres of cover crops

We took a lot of pictures of Felix

We have never worked so hard in our lives. Still, we often took shortcuts or let some projects go unfinished, or unstarted. Yet despite the fact that we haven’t had a real day off since March, I’m looking forward to next year. I know we can do a better job, and I’m oddly excited to get started. On the list for next year includes planting an orchard, fixing up the farmhouse, getting better at killing weeds, plowing 5 more acres, growing more cover crops, growing new and interesting varieties of vegetables, and, of course, spending more time playing with Felix.

Read Full Post »

Older Posts »